• Astatic PDC1 Kit
  • pdc1-5.jpg
  • pdc1-1.jpg
  • pdc1-2.jpg
  • PDC1-5.jpg
  • hs803-23.jpg
  • HS803PL-2-24.jpg
  • HS803PL-3-24.jpg
  • Astatic PDC1 Kit
  1. Home
  2. CB & Trucking
  3. Meters and Filters
  4. PDC1KIT

Astatic PDC1 SWR & Power Meter with 3' Coax Jumper

Walcott Radio PDC1KIT

X
Hassle-Free Warranty & Easy Returns

At Walcott Radio, we want you to shop with confidence! That's why we offer a straightforward warranty and a stress-free return policy to ensure you're satisfied with your purchase.

Easy Returns - No Worries!

  • Changed your mind? No problem! Return unused, unopened, and unmodified products within 30 days for a refund.
  • Some items like batteries, used/refurbished products, and custom modifications are non-refundable.

Reliable Warranty - We've Got You Covered

  • Enjoy 90 days of coverage against manufacturer defects.
  • If something isn't right, we'll help troubleshoot, and if needed, we will arrange for inspection, repair, or replacement

Customer-Focused Support

  • Need Help? Our experts are just a phone call or email away!
  • We work hard to make sure every product performs at its best - because we care about your experience.

For full details, check out our Warranty & Return Policy

X
CB Radio Technicians since 1986

Unlock the full potential of your radio with our in-house radio technican upgrade services. Don't leave any potential for performance on the table, and ensure your new radio equipment has been thoroughly tested and verified to operate at it's maximum potential.

Improved Range & Clarity

Expert Calibration for Peak Performance

Optimized for Ehanced Usability

Speak directly with the radio Technician for any operation quests

Walcott Radio 30-Day Hassle-Free Returns
In Stock
was $43.90
$40.90
Save $3.00 (7%)
Shop all Walcott Radio products

Measure your SWR & Power Rating
Includes 3' Jumper Cable

Product Highlights
  • SWR & Power Meter
  • Includes 3' Coax Jumper
  • 10 & 100 Watt Power Scales
View all features
Walcott Radio 30-Day Hassle-Free Returns
Return info
Get it quick! Most orders arrive in 2-3 days
Free Phone Support
844-925-2688 9-5 Mon-Fri

Customers Also Purchased

?
Firestik Measuring SWR and Things Every CB\'er Should Know 60999
$300
Firestik Measuring SWR and Things Every CB'er Should Know 60999
?
6 Inch Long Half Inch Wide Tinned Copper Ground Strap with Ring Terminals
$2395
6 Inch Long Half Inch Wide Tinned Copper Ground Strap with Ring Terminals
?
12\
$2895
12" Ground Strap
?
24 Inch Long Ground Strap
$3095
24 Inch Long Ground Strap
?
12 Foot Length Heavy Duty CB Coax Cable w. Removeable PL259 Connector 128XN13
$2695
12 Foot Length Heavy Duty CB Coax Cable w. Removeable PL259 Connector 128XN13
?
18\' CB Coax Cable w. Removeable PL259 Connector 188XN13
$2995
18' CB Coax Cable w. Removeable PL259 Connector 188XN13
?
18\'x2 DH18N13 - Dual Coax W Removeable Ends - Easy Install
$3995
18'x2 DH18N13 - Dual Coax W Removeable Ends - Easy Install
See More ▽
Get Expert Help and Assistance
from people who have hands-on knowledge
📞 1-844-925-2688
M-F 10am to 5pm CST
  • Description

Measure your SWR & Power Rating
Includes 3' Jumper Cable

It's important to make sure your antenna system is tuned in and working efficiently. Not only can it affect your performance, but issues with high SWR can actually damage your radio. We make it simple to get your SWR checked and tuned in with this package of an Astatic PDC1 SWR / Power Meter & 3 foot coax jumper.

Not only will the PDC1 help you get your antenna tuned to your vehicle, but it also acts as a power meter to test the output of your radio. Switch between 10 watt or 100 watt scale to get a closer look at your output power.

PDC1KIT Technical Specifications

Power Handling100 watts
Coax TypeRG58
Coax Length3'
Coax Connections2 x PL-259
Step-by-Step Antenna Tuning Guide:

1. Install the SWR Meter in Line
Turn off your radio. Locate the coaxial cable connecting your radio to the antenna.
Disconnect the coaxial cable from the back of the radio.
Connect the coaxial cable coming from the antenna to the antenna (ANT) port on the SWR meter.
Use a short length of coax to connect the transceiver (TX) port on the SWR meter to the radio's antenna jack.

2. Set the Meter to FWD (Forward)
Turn the SWR meter's switch to the FWD position.
Set your radio to the lowest possible power output (usually in AM or CW mode).
Select the frequency or channel where you intend to test your antenna's SWR (usually near the middle of the band).
Key the microphone (transmit without speaking) or use a CW key to transmit a steady signal.

3. Calibrate the SWR Meter
While holding down the transmit button (keyed up), adjust the calibration (CAL) knob on the SWR meter.
Turn the knob until the needle is aligned with the SET mark on the meter's scale (usually located near the far right side).
This step ensures the meter is correctly reading the forward power (transmitted signal).

4. Switch to REF (Reflect)
After calibrating the meter in FWD mode, release the transmit button and switch the meter to REF (Reflect).
Key the microphone again (transmit) to check the reflected power reading, which indicates how much of the transmitted power is being reflected back from the antenna.

5. Interpret the Results
Low SWR (around 1:1 to 1.5:1): Indicates a well-matched antenna system with minimal power reflected.
Moderate SWR (1.5:1 to 2:1): This is acceptable but may indicate some room for improvement in the antenna tuning or placement.
High SWR (above 2:1): Indicates significant reflected power, which could harm your transmitter. You may need to adjust your antenna or use a different one to bring the SWR down.

6. Adjust Antenna if Necessary
If your SWR reading is too high, adjust the antenna's length or position and re-test.
Repeat steps 2-5 after each adjustment to check if the SWR has improved.

7. Turn Off the SWR Meter
After taking the readings, turn off the radio and disconnect the SWR meter.
Reconnect the coaxial cable from the antenna directly to the radio.
Tips for Best Results
Test across multiple frequencies to ensure your antenna performs well across the whole band.

Always start with low power to avoid damage to your equipment. Keep your coaxial cables in good condition to avoid issues with the SWR readings caused by damaged cabling.

What is an SWR meter and why would I need one?

SWR (Standing Wave Ratio) meters measure the efficiency of your antenna system by comparing the power sent to the antenna and the power reflected back. A low SWR indicates that your antenna is well-tuned and is efficiently transmitting your signal, reducing the risk of damaging your CB radio.

How do I connect an SWR meter to my CB radio and antenna?

1. Connect the cable from your antenna system into the "ANT" connection on the back of the meter.
2. Take one end of a short jumper cable and connect it into the "TRANS" (the front is labeled "TX") connector on the meter.
3. Take the other end of the jumper cable and attach it to the CB radio's antenna jack

What if my SWR is high on all channels?

A high SWR across all channels indicates there's something wrong in your antenna setup. Here are some of the most common problems in getting your antenna tuned.

• Poor ground connection - Most mobile antennas need a good ground plane to work properly. Ensure your antenna mount has a solid electrical connection to the vehicle's chassis. Clean paint, rust, and dirt from the mounting surface. If your vehicle has non-metallic parts like RV's and sports carts or if the ground plane is inadequate, you can install ground straps to connect different metal parts of the vehicle, enhancing the overall ground plane.

• Bad coaxial cable or connectors - Inspect the cable and look for damage along the cable. If you see corrosion on the cable or connectors it's time for them to be replaced. • Improper installation - Check to make sure the antenna mount is attached and check your antenna stud to ensure the nylon washer is where it should be. If you have an antenna stud make sure your nylon washer is in the correct spot. For studs with a PL-259 the isolation washer should be just above the bracket.

• Obstructions - Nearby obstructions can affect your readings. Make sure you're in an open area and that the antenna is positioned so the signal won't be reflected off of the vehicle body or cab.

How do I test my radio's power ouput with this meter?

Flip the right switch into the PWR position and set the left switch based off of your power range. For your basic CB radio the 10 Watt position will do, or switch into the 100 watt scale if you're using more than 10 watts. Key down on your microphone without speaking to read your RF power (deadkey). Key the microphone and talk directly into the mic to check your modulation or swing wattage.

Walcott Radio PDC1KIT Reviews

Write a Review
The world's leading CB radio and radio communication store. Same-day shipping. Hands-on experience. Get talkin', we'll help!

Contact Us

📍
  • Walcott Radio
  • 2940 N Plainview Rd Walcott
  • Walcott, IA 52773
📞
  • Phone Support
  • 1-844-925-2688
  • M-F 10am to 5pm CST
🕘
  • Store Hours
  • M-F 9am-6pm
  • Sat 9am-5pm
  • Sun Closed
Shop
My Account
Customer Service
Company Information
​
Copyright 2025 Walcott Radio
Visit our Store! 2940 N Plainview Rd Walcott, Iowa 52773 USA